电子发烧友App
创作
发文章
发帖 
提问 
发资料
发视频资料介绍
This version (20 Nov 2020 10:33) was approved by Alexandru Ardelean.The Previously approved version (20 Nov 2020 10:30) is available.
Table of Contents
nanoDAC+ IIO DAC Linux Driver
Supported Devices
This driver supports the
Reference Circuits
Evaluation Boards
Description
This is a Linux industrial I/O (IIO) subsystem driver, targeting multi-channel serial interface DACs. The industrial I/O subsystem provides a unified framework for drivers for many different types of converters and sensors using a number of different physical interfaces (i2c, spi, etc). See IIO for more information.
Source Code
Status
Files
Devicetree
Required devicetree properties for spi devices:
- compatible: Needs to be the name of the device. E.g. “ad5676”
- reg: The chipselect number used for the device
- spi-max-frequency: Maximum SPI clock frequency.
- spi-cpol: Needs to be set for the correct SPI mode
- vcc-supply: Phandle to the fixed regulator
- interrupts: the interrupt used for buffer sampling
- pwms: pwm pin used as the interrupt source
adc_vref: fixedregulator@0 { compatible = "regulator-fixed"; regulator-name = "fixed-supply"; regulator-min-microvolt = <2500000>; regulator-max-microvolt = <2500000>; regulator-boot-on; }; #address-cells = <1>; #size-cells = <0>; status = "okay"; ad5676@0 { compatible = "ad5676"; reg = <0>; spi-max-frequency = <1000000>; spi-cpha; vcc-supply = <&adc_vref>; interrupts = <25 IRQ_TYPE_EDGE_RISING>; interrupt-parent = <&gpio>; pwms = <&pwm 0 100>; pwm-names = "pwm-trigger"; };
Required devicetree properties for i2c devices:
- compatible: Needs to be the name of the device. E.g. “AD5696”
- reg: The chipselect number used for the device
- vcc-supply: Phandle to the fixed regulator
- interrupts: the interrupt used for buffer sampling
- pwms: pwm pin used as the interrupt source
adc_vref: fixedregulator@0 {
compatible = "regulator-fixed";
regulator-name = "fixed-supply";
regulator-min-microvolt = <2500000>;
regulator-max-microvolt = <2500000>;
regulator-boot-on;
};
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
ad5696@e {
compatible = "ad5696";
reg = <0xe>;
vcc-supply = <&adc_vref>;
interrupts = <25 IRQ_TYPE_EDGE_RISING>;
interrupt-parent = <&gpio>;
pwms = <&pwm 0 100>;
pwm-names = "pwm-trigger";
};
Driver testing
This specifies any shell prompt running on the target
root:/> cd /sys/bus/iio/devices/ root:/sys/bus/iio/devices> ls iio:device0 root:/sys/bus/iio/devices> cd iio/:device0 root:/sys/bus/iio/devices/iio:device0> ls -l drwxr-xr-x 2 root root 0 Jul 31 15:17 buffer -r--r--r-- 1 root root 4096 Jul 31 15:17 dev -r--r--r-- 1 root root 4096 Jul 31 15:17 name lrwxrwxrwx 1 root root 0 Jul 31 15:17 of_node -> ../../../../../../../../firmware/devicetree/base/soc/spi@7e204000/ad5679r@0 -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage0_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage0_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage0_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage10_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage10_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage10_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage11_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage11_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage11_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage12_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage12_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage12_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage13_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage13_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage13_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage14_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage14_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage14_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage15_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage15_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage15_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage1_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage1_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage1_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage2_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage2_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage2_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage3_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage3_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage3_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage4_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage4_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage4_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage5_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage5_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage5_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage6_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage6_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage6_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage7_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage7_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage7_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage8_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage8_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage8_raw -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage9_powerdown -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage9_powerdown_mode -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage9_raw -r--r--r-- 1 root root 4096 Jul 31 15:17 out_voltage_powerdown_mode_available -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage_sampling_frequency -rw-r--r-- 1 root root 4096 Jul 31 15:17 out_voltage_scale drwxr-xr-x 2 root root 0 Jul 31 15:17 power drwxr-xr-x 2 root root 0 Jul 31 15:17 scan_elements lrwxrwxrwx 1 root root 0 Jul 31 15:17 subsystem -> ../../../../../../../../bus/iio drwxr-xr-x 2 root root 0 Jul 31 15:17 trigger -rw-r--r-- 1 root root 4096 Jul 31 15:17 uevent
Show device name
This specifies any shell prompt running on the target
root:/sys/bus/iio/devices/iio:device0> cat name ad5696
Show scale
Description:
scale to be applied to in_voltage0_raw in order to obtain the measured voltage in millivolts.
This specifies any shell prompt running on the target
root:/sys/bus/iio/devices/iio:device0> cat out_voltage_scale 0.038146972
Set channel Y output voltage
Description:
/sys/bus/iio/devices/deviceX/out_voltageY_raw
Raw (unscaled, no bias etc.) output voltage for channel Y.
This specifies any shell prompt running on the target
root:/sys/bus/iio/devices/iio:device0> echo 10000 > out_voltage0_raw
U = out_voltage0_raw * out_voltage_scale = 10000 * 0.038140 = 381.40 mV
List available power down modes
/sys/bus/iio/devices/deviceX/out_powerdown_mode_available
Description:
Lists all available output power down modes.
This specifies any shell prompt running on the target
root:/sys/bus/iio/devices/iio:device0> cat out_voltage_powerdown_mode_available 1kohm_to_gnd 100kohm_to_gnd three_state
Set channel Y power down mode
/sys/bus/iio/devices/deviceX/out_voltageY_powerdown_mode
Description:
Specifies the output power down mode.
DAC output stage is disconnected from the amplifier and
| 1kohm_to_gnd | connected to ground via an 1kOhm resistor |
| 100kohm_to_gnd | connected to ground via an 100kOhm resistor |
| three_state | left floating |
For a list of available output power down options read out_voltageX_powerdown_mode_available.
This specifies any shell prompt running on the target
root:/sys/bus/iio/devices/iio:device0> echo three_state > out_voltage0_powerdown_mode root:/sys/bus/iio/devices/iio:device0> cat out_voltage0_powerdown_mode three_state
Enable power down mode on output Y
/sys/bus/iio/devices/deviceX/out_voltageY_powerdown
Description:
Writing 1 causes output Y to enter the power down mode specified
by the corresponding out_voltageY_powerdown_mode. Clearing returns to
normal operation. Y may be suppressed if all outputs are
controlled together.
This specifies any shell prompt running on the target
root:/sys/bus/iio/devices/iio:device0> echo 1 > out_voltage0_powerdown root:/sys/bus/iio/devices/iio:device0> cat out_voltage0_powerdown 1 root:/sys/bus/iio/devices/iio:device0> echo 0 > out_voltage0_powerdown root:/sys/bus/iio/devices/iio:device0> cat out_voltage0_powerdown 0
Buffer Support
Description:
The nanoDAC family of devices has buffer support for changing the output of the DAC channels. To achieve this a PWM signal is used as the device trigger to output data. Using a sampling frequency attribute the period of the PWM signal can be changed. The sampling frequency is in Hz.
In order to use this functionality the interrupt pin must be tied to the PWM generation pin
This specifies any shell prompt running on the target
root@analog:/sys/bus/iio/devices/iio:device0 $ cat out_voltage_sampling_frequency 1000 root@analog:/sys/bus/iio/devices/iio:device0# echo 2000 > out_voltage_sampling_frequency root@analog:/sys/bus/iio/devices/iio:device0# cat out_voltage_sampling_frequency 2000
Enable buffered channels
Description:
The user has to enable on what channels to output the buffer samples. The samples are interleaved in the following in the order of the enabled channels.
Example:
sample_ch0|sample_ch1|sample_ch2
If only channel 1 is enabled the buffer samples will have the following configuration:
sample_ch1|sample_ch1|sample_ch1
This specifies any shell prompt running on the target
root@analog:/sys/bus/iio/devices/iio:device0# cd scan_elements/ root@analog:/sys/bus/iio/devices/iio:device0/scan_elements# ls out_voltage0_en out_voltage10_type out_voltage12_index out_voltage14_en out_voltage15_type out_voltage2_index out_voltage4_en out_voltage5_type out_voltage7_index out_voltage9_en out_voltage0_index out_voltage11_en out_voltage12_type out_voltage14_index out_voltage1_en out_voltage2_type out_voltage4_index out_voltage6_en out_voltage7_type out_voltage9_index out_voltage0_type out_voltage11_index out_voltage13_en out_voltage14_type out_voltage1_index out_voltage3_en out_voltage4_type out_voltage6_index out_voltage8_en out_voltage9_type out_voltage10_en out_voltage11_type out_voltage13_index out_voltage15_en out_voltage1_type out_voltage3_index out_voltage5_en out_voltage6_type out_voltage8_index out_voltage10_index out_voltage12_en out_voltage13_type out_voltage15_index out_voltage2_en out_voltage3_type out_voltage5_index out_voltage7_en out_voltage8_type root@analog:/sys/bus/iio/devices/iio:device0/scan_elements# echo 1 > out_voltage0_en root@analog:/sys/bus/iio/devices/iio:device0/scan_elements# cd ../buffer/ root@analog:/sys/bus/iio/devices/iio:device0/buffer# ls data_available enable length watermark root@analog:/sys/bus/iio/devices/iio:device0/buffer# echo 1 > enable
Sending a buffer sample example:
This specifies any shell prompt running on the target
root@analog:/sys/bus/iio/devices/iio:device0/buffer# echo -n -e '/x22/x33' > /dev/iio/:device0
More Information
- IIO mailing list: linux [dash] iio [at] vger [dot] kernel [dot] org
下载该资料的人也在下载
下载该资料的人还在阅读
更多 >
- AD5449 IIO DAC Linux驱动程序 3次下载
- AD5380 IIO多通道Linux驱动程序DAC 8次下载
- AD7291 IIO ADC Linux驱动程序 3次下载
- AD5064 IIO四通道Linux驱动程序DAC 5次下载
- AD5421 IIO DAC Linux驱动程序 2次下载
- AD5360 IIO多通道Linux驱动程序DAC 7次下载
- AD7303 IIO DAC Linux驱动程序 1次下载
- AD5446 IIO DAC Linux驱动程序 7次下载
- AD5624 IIO四通道Linux驱动程序DAC 7次下载
- IIO单通道串行ADC Linux驱动程序 4次下载
- AD9834 IIO直接数字合成Linux驱动程序 1次下载
- AD9832 IIO直接数字合成Linux驱动程序 3次下载
- AD7998 IIO ADC Linux驱动程序 14次下载
- AD7887 IIO ADC Linux驱动程序 6次下载
- AD5677R NanDAC+无操作系统驱动程序 13次下载
- 怎么编写Framebuffer驱动程序 66次阅读
- 基于V4L技术和摄像头的Linux驱动程序的设计与实现 2621次阅读
- ProfiNet输入/输出端的驱动程序解析 3140次阅读
- 如何写一个Linux设备驱动程序 4018次阅读
- 米尔科技LINUX设备驱动程序教程 1781次阅读
- 嵌入式Linux内核的驱动程序开发是怎样的 1284次阅读
- 浅谈电脑驱动程序的工作原理 详解电脑驱动程序意义 2.8w次阅读
- 基于嵌入式Linux内核的系统设备驱动程序开发设计 1031次阅读
- 基于Linux2.6.30开发DS18B20的驱动程序的类型和文件操作接口函数详解 1262次阅读
- 可动态安装的Linux设备驱动程序 882次阅读
- 如何用嵌入式Linux系统编写键盘驱动 1222次阅读
- 8255A驱动程序 2868次阅读
- 8155驱动程序 2784次阅读
- Xilinx设备的驱动程序 7711次阅读
- PCI驱动程序开发实例 6506次阅读
上传资料赚积分下载排行
本周
- 1电子电路原理第七版PDF电子教材免费下载
- 0.00 MB | 1491次下载 | 免费
- 2单片机典型实例介绍
- 18.19 MB | 95次下载 | 1 积分
- 3S7-200PLC编程实例详细资料
- 1.17 MB | 27次下载 | 1 积分
- 4笔记本电脑主板的元件识别和讲解说明
- 4.28 MB | 18次下载 | 4 积分
- 5开关电源原理及各功能电路详解
- 0.38 MB | 11次下载 | 免费
- 6100W短波放大电路图
- 0.05 MB | 4次下载 | 3 积分
- 7基于单片机和 SG3525的程控开关电源设计
- 0.23 MB | 4次下载 | 免费
- 8基于AT89C2051/4051单片机编程器的实验
- 0.11 MB | 4次下载 | 免费
本月
- 1OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234313次下载 | 免费
- 2PADS 9.0 2009最新版 -下载
- 0.00 MB | 66304次下载 | 免费
- 3protel99下载protel99软件下载(中文版)
- 0.00 MB | 51209次下载 | 免费
- 4LabView 8.0 专业版下载 (3CD完整版)
- 0.00 MB | 51043次下载 | 免费
- 5555集成电路应用800例(新编版)
- 0.00 MB | 33562次下载 | 免费
- 6接口电路图大全
- 未知 | 30320次下载 | 免费
- 7Multisim 10下载Multisim 10 中文版
- 0.00 MB | 28588次下载 | 免费
- 8开关电源设计实例指南
- 未知 | 21539次下载 | 免费
总榜
- 1matlab软件下载入口
- 未知 | 935053次下载 | 免费
- 2protel99se软件下载(可英文版转中文版)
- 78.1 MB | 537793次下载 | 免费
- 3MATLAB 7.1 下载 (含软件介绍)
- 未知 | 420026次下载 | 免费
- 4OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234313次下载 | 免费
- 5Altium DXP2002下载入口
- 未知 | 233046次下载 | 免费
- 6电路仿真软件multisim 10.0免费下载
- 340992 | 191183次下载 | 免费
- 7十天学会AVR单片机与C语言视频教程 下载
- 158M | 183277次下载 | 免费
- 8proe5.0野火版下载(中文版免费下载)
- 未知 | 138039次下载 | 免费
工商网监
评论