资料介绍
Two Stage RIAA Phono Preamplifier
Designers of quality audio equipment have long recognized the value of a low noise gain block with“audiophile performance”。 The LM833 is such a device: a dual operational amplifier with excellent audio specifications. The LM833 features low input noise voltage typical), large gainbandwidth product (15 MHz), high slew rate (7V/μSec), low THD (0.002% 20 Hz-20 kHz), and unity gain stability.
A phono preamplifier‘s primary task is to provide gain (usually 30 to 40 dB at 1 kHz) and accurate amplitude and phase equalization to the signal from a moving magnet or a moving coil cartridge. (A moving coil device’s output voltage is typically around 20 dB lower than that of a moving magnet pickup, so this signal is usually amplified by a step-up device—either an active circuit or a transformer—before being applied to the input of the phono preamplifier)。 In addition to the amplification and equalization functions, the phono preamp must not add significant noise or distortion to the signal from the cartridge.
Figure 1 shows the standard RIAA phono preamplifier amplitude response. Numerical values relative to the 1 kHz gain are given in Table 1. Note that the gain rolls off at a 6 dB/octave rate above 2122 Hz. Most phono preamplifier circuits in commercially available audio products, as well as most published circuits, are based on the topology shown in Figure 2(a)。 The network consisting of R1, R2, C1, and C2 is not unique, and can be replaced by any of several other networks that give equivalent results. R0 is generally well under 1k to keep its contribution to the input noise voltage below that of the cartridge itself. The 47k resistor shunting the input provides damping for moving-magnet phono cartridges. The input is also shunted by a capacitance equal to the sum of the input cable capacitance and Cp. This capacitance resonates with the inductance of the moving magnet cartridge around 15 kHz to 20 kHz to determine the frequency response of the transducer, so when a moving magnet pickup is used, Cp should be carefully chosen so that the total capacitance is equal to the recommended load capitance for that particular cartridge..
- DIY板载低音吉他前置放大器 16次下载
- 2通道前置放大器音频板开源分享 16次下载
- 低功率麦克风前置放大器 4次下载
- ZVEX前置放大器踏板开源 7次下载
- 麦克风前置放大器和处理器 4次下载
- EQD Arrows前置放大器助推器 0次下载
- 数字CMOS麦克风前置放大器的单位参数综述 4次下载
- 全平衡无环路负反馈_电子管前置放大器 41次下载
- 低阻抗话筒前置放大器电路原理图免费下载 40次下载
- 前置放大器 0次下载
- 光电二极管前置放大器设计 0次下载
- 电流模跨阻型前置放大器的设计 61次下载
- 低噪声前置放大器电路的设计方法 132次下载
- 基于移动医疗服务系统中的前置放大器设计与实现 56次下载
- 视频前置放大器电路图 92次下载
- 用于2.5mV信号的运算/前置放大器电路 2103次阅读
- 分享一个吉他前置放大器电路 1573次阅读
- 基于LM382的通用前置放大器电路 1013次阅读
- 麦克风前置放大器的工作原理及电路图 5982次阅读
- 低音炮前置放大器原理图分享 1761次阅读
- 带晶体管的便携式麦克风前置放大器电路 678次阅读
- 具有低音增强的立体声前置放大器电路分享 1646次阅读
- 一个简单的立体声驻极体麦克风前置放大器电路 7685次阅读
- 一个简单低成本的电子管头真空管前置放大器电路 2132次阅读
- 前置放大器的作用及电路图 4.5w次阅读
- 前置放大器工作原理 1.2w次阅读
- 前置放大器怎么接? 1.7w次阅读
- 前置放大器的作用是什么 1.6w次阅读
- 音频前置放大器电路图大全(八款音频前置放大器电路设计原理图详解) 8.9w次阅读
- 音频前置放大器电路详解 2.6w次阅读
下载排行
本周
- 1TC358743XBG评估板参考手册
- 1.36 MB | 330次下载 | 免费
- 2开关电源基础知识
- 5.73 MB | 11次下载 | 免费
- 3100W短波放大电路图
- 0.05 MB | 4次下载 | 3 积分
- 4嵌入式linux-聊天程序设计
- 0.60 MB | 3次下载 | 免费
- 5DIY动手组装LED电子显示屏
- 0.98 MB | 3次下载 | 免费
- 651单片机大棚环境控制器仿真程序
- 1.10 MB | 2次下载 | 免费
- 751单片机PM2.5检测系统程序
- 0.83 MB | 2次下载 | 免费
- 8TP4055-500mA线性锂离子电池充电器数据手册
- 0.27 MB | 2次下载 | 免费
本月
- 1OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234315次下载 | 免费
- 2555集成电路应用800例(新编版)
- 0.00 MB | 33566次下载 | 免费
- 3接口电路图大全
- 未知 | 30323次下载 | 免费
- 4开关电源设计实例指南
- 未知 | 21549次下载 | 免费
- 5电气工程师手册免费下载(新编第二版pdf电子书)
- 0.00 MB | 15349次下载 | 免费
- 6数字电路基础pdf(下载)
- 未知 | 13750次下载 | 免费
- 7电子制作实例集锦 下载
- 未知 | 8113次下载 | 免费
- 8《LED驱动电路设计》 温德尔著
- 0.00 MB | 6656次下载 | 免费
总榜
- 1matlab软件下载入口
- 未知 | 935054次下载 | 免费
- 2protel99se软件下载(可英文版转中文版)
- 78.1 MB | 537797次下载 | 免费
- 3MATLAB 7.1 下载 (含软件介绍)
- 未知 | 420027次下载 | 免费
- 4OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234315次下载 | 免费
- 5Altium DXP2002下载入口
- 未知 | 233046次下载 | 免费
- 6电路仿真软件multisim 10.0免费下载
- 340992 | 191186次下载 | 免费
- 7十天学会AVR单片机与C语言视频教程 下载
- 158M | 183279次下载 | 免费
- 8proe5.0野火版下载(中文版免费下载)
- 未知 | 138040次下载 | 免费
评论
查看更多