资料介绍
DESCRIPTION/ORDERING INFORMATION
The TUSB2046B is a 3.3-V CMOS hub device that provides one upstream port and four downstream ports in
compliance with the Universal Serial Bus (USB) specification as a full-speed hub. Because this device is
implemented with a digital state machine instead of a microcontroller, no firmware programming is required.
Fully-compliant USB transceivers are integrated into the ASIC for all upstream and downstream ports. The
downstream ports support both full-speed and low-speed devices by automatically setting the slew rate according
to the speed of the device attached to the ports. The configuration of the BUSPWR terminal selects either the
bus-powered or the self-powered mode.
Configuring the GANGED input determines the power switching and overcurrent detection modes for the
downstream ports. External power-management devices, such as the TPS2044, are required to control the 5-V
source to the downstream ports according to the corresponding values of the PWRON terminal. Upon detecting
any overcurrent conditions, the power-management device sets the corresponding OVRCUR terminal of the
TUSB2046B to a logic low. If GANGED is high, all PWRON outputs switch together and if any OVRCUR is
activated, all ports transition to the power-off state. If GANGED is low, the PWRON outputs and OVRCUR inputs
operate on a per-port basis.
The TUSB2046B provides the flexibility of using a 6-MHz or a 48-MHz clock. The logic level of the TSTMODE
terminal controls the selection of the clock source. When TSTMODE is low, the output of the internal APLL
circuitry is selected to drive the internal core of the device. When TSTMODE is high, the TSTPLL/48MCLK input
is selected as the input clock source and the APLL circuitry is powered down and bypassed. The internal
oscillator cell is also powered down while TSTMODE is high.
Low EMI emission is achieved because the TUSB2046B is able to utilize a 6-MHz crystal input. Connect the
crystal as shown in Figure 6. An internal PLL then generates the 48-MHz clock used to sample data from the
upstream port and to synchronize the 12 MHz used for the USB clock. If low-power suspend and resume are
desired, a passive crystal or resonator must be used. However, a 6-MHz oscillator may be used by connecting
the output to the XTAL1 terminal and leaving the XTAL2 terminal open. The oscillator TTL output must not
exceed 3.6 V.
For 48-MHz operation, the clock cannot be generated with a crystal using the XTAL2 output because the internal
oscillator cell supports only the fundamental frequency.
See Figure 7 and Figure 8 in the input clock configuration section for more detailed information regarding the
input clock configuration.
The TUSB2046B is a 3.3-V CMOS hub device that provides one upstream port and four downstream ports in
compliance with the Universal Serial Bus (USB) specification as a full-speed hub. Because this device is
implemented with a digital state machine instead of a microcontroller, no firmware programming is required.
Fully-compliant USB transceivers are integrated into the ASIC for all upstream and downstream ports. The
downstream ports support both full-speed and low-speed devices by automatically setting the slew rate according
to the speed of the device attached to the ports. The configuration of the BUSPWR terminal selects either the
bus-powered or the self-powered mode.
Configuring the GANGED input determines the power switching and overcurrent detection modes for the
downstream ports. External power-management devices, such as the TPS2044, are required to control the 5-V
source to the downstream ports according to the corresponding values of the PWRON terminal. Upon detecting
any overcurrent conditions, the power-management device sets the corresponding OVRCUR terminal of the
TUSB2046B to a logic low. If GANGED is high, all PWRON outputs switch together and if any OVRCUR is
activated, all ports transition to the power-off state. If GANGED is low, the PWRON outputs and OVRCUR inputs
operate on a per-port basis.
The TUSB2046B provides the flexibility of using a 6-MHz or a 48-MHz clock. The logic level of the TSTMODE
terminal controls the selection of the clock source. When TSTMODE is low, the output of the internal APLL
circuitry is selected to drive the internal core of the device. When TSTMODE is high, the TSTPLL/48MCLK input
is selected as the input clock source and the APLL circuitry is powered down and bypassed. The internal
oscillator cell is also powered down while TSTMODE is high.
Low EMI emission is achieved because the TUSB2046B is able to utilize a 6-MHz crystal input. Connect the
crystal as shown in Figure 6. An internal PLL then generates the 48-MHz clock used to sample data from the
upstream port and to synchronize the 12 MHz used for the USB clock. If low-power suspend and resume are
desired, a passive crystal or resonator must be used. However, a 6-MHz oscillator may be used by connecting
the output to the XTAL1 terminal and leaving the XTAL2 terminal open. The oscillator TTL output must not
exceed 3.6 V.
For 48-MHz operation, the clock cannot be generated with a crystal using the XTAL2 output because the internal
oscillator cell supports only the fundamental frequency.
See Figure 7 and Figure 8 in the input clock configuration section for more detailed information regarding the
input clock configuration.
下载该资料的人也在下载
下载该资料的人还在阅读
更多 >
- USB3.0 HUB的资料 123次下载
- 触摸屏控制器XPT2046数据手册下载 25次下载
- DC2046A-C-原理图 2次下载
- TUSB8040_USB_3.0_Four_Port_Hub_Data_Manual 15次下载
- TUSB1105,TUSB1106,pdf(Advanced 16次下载
- TUSB6250,pdf(USB 2.0 to ATA/AT 42次下载
- TUSB3410,TUSB3410I,pdf(USB to 71次下载
- TUSB3210,pdf(Universal Serial 35次下载
- TUSB2136,pdf(Universal Serial 13次下载
- TUSB2077A,pdf(7-Port Hub for t 22次下载
- TUSB2046B Errata 12次下载
- TUSB2036,pdf(2/3-Port Hub for 15次下载
- TUSB1310:世界首款分立超高速USB3.0收发器 281次下载
- TUSB1310,pdf (具有PIPE3和ULPI接口的超 89次下载
- TC6102 pdf datasheet (2 PORT 1 14次下载
- USB-C Port的Data Role、Power Role工作原理介绍 578次阅读
- 如何改变Port端口的交叉参考显示? 442次阅读
- 基于瑞萨R7FA2E1A72DFL MCU制作双机位切换的USB HUB 776次阅读
- Pytorch Hub两行代码搞定YOLOv5推理 669次阅读
- 使用PCAM和Display Port添加IP内核展示FPGA处理图像的能力 1968次阅读
- dfrobotZero/Zero W microUSB Hub分线器简介 1628次阅读
- 微雪电子USB集线器|USB HUB HAT简介 2575次阅读
- 4端口的USB3.0的HUB用的最多的是GL3520方案 3.3w次阅读
- 详解usb枚举流程 7017次阅读
- 汽车胎压监测系统的原理图 3.9w次阅读
- USB在Linux里的结构框架是什么样的?USB Core和Hub是什么? 1.9w次阅读
- 使用pdf解析可以用来读取PDF文件中字符串文本,图片数据 1.3w次阅读
- XPT2046触摸屏实验过程详解与STM32代码解析 2.3w次阅读
- XPT2046中文资料详解_引脚图及功能_工作原理_内部框图及应用设计电路 15.5w次阅读
- HFSS端口Wave Port和Lumped Port的介绍 2.9w次阅读
下载排行
本周
- 1TC358743XBG评估板参考手册
- 1.36 MB | 330次下载 | 免费
- 2开关电源基础知识
- 5.73 MB | 11次下载 | 免费
- 3嵌入式linux-聊天程序设计
- 0.60 MB | 3次下载 | 免费
- 4DIY动手组装LED电子显示屏
- 0.98 MB | 3次下载 | 免费
- 5基于FPGA的C8051F单片机开发板设计
- 0.70 MB | 2次下载 | 免费
- 651单片机窗帘控制器仿真程序
- 1.93 MB | 2次下载 | 免费
- 751单片机PM2.5检测系统程序
- 0.83 MB | 2次下载 | 免费
- 8基于51单片机的RGB调色灯程序仿真
- 0.86 MB | 2次下载 | 免费
本月
- 1OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234315次下载 | 免费
- 2555集成电路应用800例(新编版)
- 0.00 MB | 33566次下载 | 免费
- 3接口电路图大全
- 未知 | 30323次下载 | 免费
- 4开关电源设计实例指南
- 未知 | 21549次下载 | 免费
- 5电气工程师手册免费下载(新编第二版pdf电子书)
- 0.00 MB | 15349次下载 | 免费
- 6数字电路基础pdf(下载)
- 未知 | 13750次下载 | 免费
- 7电子制作实例集锦 下载
- 未知 | 8113次下载 | 免费
- 8《LED驱动电路设计》 温德尔著
- 0.00 MB | 6656次下载 | 免费
总榜
- 1matlab软件下载入口
- 未知 | 935054次下载 | 免费
- 2protel99se软件下载(可英文版转中文版)
- 78.1 MB | 537798次下载 | 免费
- 3MATLAB 7.1 下载 (含软件介绍)
- 未知 | 420027次下载 | 免费
- 4OrCAD10.5下载OrCAD10.5中文版软件
- 0.00 MB | 234315次下载 | 免费
- 5Altium DXP2002下载入口
- 未知 | 233046次下载 | 免费
- 6电路仿真软件multisim 10.0免费下载
- 340992 | 191186次下载 | 免费
- 7十天学会AVR单片机与C语言视频教程 下载
- 158M | 183279次下载 | 免费
- 8proe5.0野火版下载(中文版免费下载)
- 未知 | 138040次下载 | 免费
评论
查看更多