飞思卡尔智能车--摄像头资料3
#include "hidef.h"
#include "non_bank.sgm"
#include "runtime.sgm"
#ifndef __HCS12X__ /* it's different for the HCS12X. See the text below at the #else // __HCS12X__ */
/*
According to the -Cp option of the compiler the
__DPAGE__, __PPAGE__ and __EPAGE__ macros are defined.
If none of them is given as argument, then no page accesses should occur and
this runtime routine should not be used !
To be on the save side, the runtime routines are created anyway.
If some of the -Cp options are given an adapted versions which only covers the
needed cases is produced.
*/
/* if no compiler option -Cp is given, it is assumed that all possible are given : */
/* Compile with option -DHCS12 to activate this code */
#if defined(HCS12) || defined(_HCS12) || defined(__HCS12__) /* HCS12 family has PPAGE register only at 0x30 */
#define PPAGE_ADDR (0x30+REGISTER_BASE)
#ifndef __PPAGE__ /* may be set already by option -CPPPAGE */
#define __PPAGE__
#endif
/* Compile with option -DDG128 to activate this code */
#elif defined DG128 /* HC912DG128 derivative has PPAGE register only at 0xFF */
#define PPAGE_ADDR (0xFF+REGISTER_BASE)
#ifndef __PPAGE__ /* may be set already by option -CPPPAGE */
#define __PPAGE__
#endif
#elif defined(HC812A4)
/* all setting default to A4 already */
#endif
#if !defined(__EPAGE__) && !defined(__PPAGE__) && !defined(__DPAGE__)
/* as default use all page registers */
#define __DPAGE__
#define __EPAGE__
#define __PPAGE__
#endif
/* modify the following defines to your memory configuration */
#define EPAGE_LOW_BOUND 0x400u
#define EPAGE_HIGH_BOUND 0x7ffu
#define DPAGE_LOW_BOUND 0x7000u
#define DPAGE_HIGH_BOUND 0x7fffu
#define PPAGE_LOW_BOUND (DPAGE_HIGH_BOUND+1)
#define PPAGE_HIGH_BOUND 0xBFFFu
#define REGISTER_BASE 0x0u
#ifndef DPAGE_ADDR
#define DPAGE_ADDR (0x34u+REGISTER_BASE)
#endif
#ifndef EPAGE_ADDR
#define EPAGE_ADDR (0x36u+REGISTER_BASE)
#endif
#ifndef PPAGE_ADDR
#define PPAGE_ADDR (0x35u+REGISTER_BASE)
#endif
/*
The following parts about the defines are assumed in the code of _GET_PAGE_REG :
- the memory region controlled by DPAGE is above the area controlled by the EPAGE and
below the area controlled by the PPAGE.
- the lower bound of the PPAGE area is equal to be the higher bound of the DPAGE area + 1
*/
#if EPAGE_LOW_BOUND >= EPAGE_HIGH_BOUND || EPAGE_HIGH_BOUND >= DPAGE_LOW_BOUND || DPAGE_LOW_BOUND >= DPAGE_HIGH_BOUND || DPAGE_HIGH_BOUND >= PPAGE_LOW_BOUND || PPAGE_LOW_BOUND >= PPAGE_HIGH_BOUND
#error /* please adapt _GET_PAGE_REG for this non default page configuration */
#endif
#if DPAGE_HIGH_BOUND+1 != PPAGE_LOW_BOUND
#error /* please adapt _GET_PAGE_REG for this non default page configuration */
#endif
/* this module does either control if any access is in the bounds of the specified page or */
/* ,if only one page is specified, just use this page. */
/* This behavior is controlled by the define USE_SEVERAL_PAGES. */
/* If !USE_SEVERAL_PAGES does increase the performance significantly */
/* NOTE : When !USE_SEVERAL_PAGES, the page is also set for accesses outside of the area controlled */
/* by this single page. But this is should not cause problems because the page is restored to the old value before any other access could occur */
非常好我支持^.^
(82) 88.2%
不好我反对
(11) 11.8%
下载地址
飞思卡尔智能车--摄像头资料3下载
相关电子资料下载
- KT6368A的封装怎么画 原理图怎么画 资料怎么看 怎么下载呢 65
- 免费PLC学习文档和资料一般可以在哪里获取? 67
- 如何整定卡尔曼滤波的Q、R参数? 80
- 实战经验 | BlueNRG-X 原理图参数说明(附资料下载端口) 98
- Works With观看前十大热门课程,免费重温录播并下载简报资料! 137
- 华为全新智慧屏芯片鸿鹄 900 发布:智慧屏 V5 Pro 首发;高通资料泄露:骁龙 1447
- ATA-7020高压放大器产品资料 54
- RA2快速设计指南 [9] 一般布线实践与参考资料(完结) 35
- 人工神经网络算法、PID算法、Python人工智能学习等资料包分享(附源代码) 447
- 安泰ATA-7015高压放大器产品资料 86